Adlink CSA-5200 Manual do Utilizador

CSA-5200 2U Rackmount Network Appliance with Intel® Xeon® Processor E3-1200 v3 Family User’s Manual Manual Revision:

10 CSA-5200 1.5 Package Contents Before opening, please check the shipping carton for any damage. If the shipping carton and contents are damaged, n

11 CSA-5200 2 Specifications 2.1 CSA-5200 Specifications Main System CPU Intel® Xeon® E3-1275 v3 (4C/8T) Intel® Xeon® E3-1225 v3 (4C/4T) Intel® C

12 CSA-5200 Mechanical & Environmental Form Factor 19” 2U rackmount 440mm x 88mm x 460 mm (W x H x D) Fans 3x fans speed adjustable Able to opera

13 CSA-5200 3 Getting Started 3.1 Removing the Chassis Lid 1. Remove the four screws securing each side of the lid to the chassis. 2. Remove the

14 CSA-5200 4. Carefully place the CPU into the socket, making sure the socket notches align with the processor notches and the alignment triangle o

15 CSA-5200 6. Make sure there is sufficient thermal paste on of the heatsink and place it on the CPU with the cooling fins aligned with the DIMM s

16 CSA-5200 3.3 Installing a 3.5" SATA Drive 1. Loosen the screw securing the drive bracket to the chassis and lift the bracket out as shown.

17 CSA-5200 3. Install the drive/bracket assembly to the chassis, making sure the 2 tabs of the bracket fit into the slots as shown.

18 CSA-5200 3.5 Installing a Network Interface Module 3. Loosen the two screws on the Network Interface Module (NIM) faceplate, and pull outwards

19 CSA-5200 5. Insert the NIM into the slot. 6. Secure the NIM with the two screws removed in Step 1.

2 CSA-5200 Revision History Revision Release Date Description of Change(s) 1.00 18/08/2014 Initial release 1.01 25/11/2014 Remove CSA-5100; add F

20 CSA-5200 3.6 Driver Installation The CSA-5200 drivers are available from the ADLINK All-In-One DVD at X:\CSA-5200\, or from the ADLINK website at

21 CSA-5200 4 System Interfaces 4.1 Front Panel I/O 4.1.1 Status LEDs Power LED Green: Power On Bypass Status LED Red: Bypass; Off: No Bypass

22 CSA-5200 4.1.3 Service Port Status LEDs LAN LED Status LED Color 10 Mbps Off Left 100 Mbps GREEN 1000 Mbps Yellow GbE Right Right LINK wi

23 CSA-5200 4.2 Board Layout 16234 577891011 11 11 11 Location Description Location Description 1 PCIe x4 connector (PCIE1) 7 mSATA connectors (C

24 CSA-5200 4.3 Connectors and Jumpers 4.3.1 PCIe x4 Connector (PCIE1) Pin Signal Pin Signal A1 PRSNT1# B1 +12V A2 +12V B2 +12V A3 +12V B3 +12V

25 CSA-5200 4.3.2 CFast Connector (CN17) Pin Signal S1 GND S2 CF_TX_DP S3 CF_TX_DN S4 GND S5 CF_RX_DN S6 CF_RX_DP S7 GND P1 CFast_CDI P2 GND P3 NC

26 CSA-5200 4.3.4 ATX12V Connector (CN24) Pin Signal 1-4 GND 5-8 P12V_CORE 4.3.5 Fan Connectors (FAN1/FAN6-9) Pin Signal 1 FAN_CTL 2 FAN_TAC

27 CSA-5200 4.3.7 mSATA Connectors (CN9/CN48) Pin Signal Pin Signal 1 NC 2 P3V3 3 NC 4 GND 5 NC 6 P1V5 7 NC 8 NC 9 GND 10 NC 11 NC 12 NC

28 CSA-5200 4.3.9 SATADOM Power Connector (CN18, Wafer 1.25mm pitch) Pin Signal 1 Ground 2 TXP 3 TXN 4 Ground 4.3.10 Clear CMOS Jumper (JBAT1

29 CSA-5200 Pin Signal Pin Signal A29 PCIE-RXP3 B29 GND A30 PCIE-RXN3 B30 NC A31 GND B31 NC A32 NC B32 GND A33 NC B33 PCIE-TXP4 A34 GND B34

3 CSA-5200 Table of Contents Revision History ...

30 CSA-5200 5 LAN Bypass Function The CSA-5200 is equipped with a LAN Bypass function to allow uninterrupted network traffic in the case of power dis

31 CSA-5200 CSA-Z8X10 LAN Bypass Port Pairing LAN Bypass Pair 1: LAN1 & LAN2 LAN Bypass Pair 2: LAN3 & LAN4 LAN Bypass Pair 3: LAN5 &a

32 CSA-5200 5.3 SuperIO Watchdog Driver & API A SuperIO Watchdog Driver and API (Linux only) is available to enable LAN bypass by software c

33 CSA-5200 BYPASS_BTN#WDOG_REESTLAN_BYPASS_LED#Watchdog(ITE IT8786)LPCBYPASS_LAN# Active LowNetwork ControllerLAN INLAN OUTPCHHaswell CPUCSA-5200(Im

34 CSA-5200 6 Watchdog Timer Programming Some applications require a server to intelligently switch the LAN bypass mode off and on. ADLINK has develo

35 CSA-5200 6.2 Deliverables The CSA-5200 SuperIO Watchdog Software deliver package (SuperIO_WDT-x.x.x.tar.gz) provides the following software compo

36 CSA-5200 PROTOTYPE static ssize_t write(struct file *file, const char __user *data,size_t len, loff_t *ppos) DESCRIPTION This function is used to

37 CSA-5200 DESCRIPTION This function defines functions for the watchdog device according to the available features. int ioctl(int handle, int cmd,[i

38 CSA-5200 * the Watchdog to reset its internal timer so it doesn't trigger * a computer reset. */ static void keep_alive(void) { int dummy

39 CSA-5200 { flags = WDIOS_DISABLECARD; ioctl(fd, WDIOC_SETOPTIONS, &flags); fprintf(stderr, "Watchdog card disabled.\n"

4 CSA-5200 6 Watchdog Timer Programming ... 34 6.1 Architecture O

40 CSA-5200 7 BIOS Setup The following chapter describes basic navigation for the CSA-5200 BIOS setup utility. 7.1 Entering BIOS Setup To enter th

41 CSA-5200 7.2 Setup Menu The Main BIOS setup menu is the first screen that you can navigate to. The Main BIOS setup menu screen has two main frames

42 CSA-5200 →← Left/Right. The Left and Right < Arrow > keys allow you to select a setup screen. For example: Main screen, Advanced screen,

43 CSA-5200 F3 The < F3 > key on your keyboard is the optimized defaults key. To set the optimized defaults settings of the BIOS, press the

44 CSA-5200 7.4 Main Setup When you first enter the Setup Utility, you will find the Main setup screen. You can always return to the Main setup scree

45 CSA-5200 7.4.2 System Date/System Time Use this option to change the system time and date. Highlight System Time or System Date using the < A

46 CSA-5200 7.5.1 ACPI Settings You can use this screen to select options for the ACPI Advanced Configuration Settings. Use the up and down < Arr

47 CSA-5200 Hyper-threading Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optim

48 CSA-5200 7.5.3 SATA Configuration You can use this screen to select options for the SATA Configuration Settings. An example of the SATA Configur

49 CSA-5200 7.5.4 PCH-FW Configuration You can use this screen to check Intel Management Engine (ME) firmware status. The information is described

5 CSA-5200 1 Overview 1.1 Introduction The ADLINK CSA-5200 is a 2U 19" rackmount Network Appliance with 4th Generation Intel® processor Xeon®

50 CSA-5200 Legacy USB Support Enables legacy USB support. Auto option disables legacy support if no USB devices are connected. The disable option wi

51 CSA-5200 7.5.7 IT8786 HW Monitor You can use this screen to check PC health status. The information will be described on the following pages.

52 CSA-5200 5V Displays current system 5V voltage. 12V Displays current system 12V voltage. 7.5.8 Smart Fan Function You can use this screen to se

53 CSA-5200 PWM-Plus start temperature limit FAN will start addition RPM, when temperature is higher than this limit. Fan full temperature limit Fan

54 CSA-5200 Console Redirection The BIOS Console Redirection feature is here. Set this value to Enabled/Disabled. Console Redirection Settings The se

55 CSA-5200 Stop Bits Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit.

56 CSA-5200 7.6 Chipset Setup Select the Chipset tab from the setup screen to enter the Chipset BIOS Setup screen. You can select any of Chipset BIOS

57 CSA-5200 7.6.1.1 PCI Express Configuration PCI Express Root Port 3,4,5 Control the PCI Express Root Port of 3-5. Set this value to Enable / Di

58 CSA-5200 7.6.2 System Agent (SA) Configuration VT-d The Intel Virtualization Technology for Directed I/O. Set this value to Enabled/Disabled.

59 CSA-5200 7.6.2.1 Graphics Configuration Primary Display Select which of IGFX/PEG/ PCIE graphics device should be the primary display. Set this v

6 CSA-5200 1.2 Block Diagram Intel®Xeon® E3-1200 v3Intel PCHC226DMI 2.0 x4SATA x4SPIto NIM slotsBIOSGPIOUDIMMDDR3 1600MHzNIM slot (PCIe x8, GPIO)

60 CSA-5200 DVMT Total Gfx Memory Select DVMT 5.0 total graphic memory size used by the internal graphics device. Configuration options are as seen

61 CSA-5200 7.7 Boot Setup Select the Boot tab from the setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left

62 CSA-5200 Hard Drive BBS Priorities Specifies the boot device priority sequence from available hard drives. CSM16 Parameters You can use this scree

63 CSA-5200 Administrator / User Password If only the administrator’s password is set, then this limits access to setup and is only asked for when e

64 CSA-5200 Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset Reset the system after saving the change

65 CSA-5200 Restore Defaults Restore/Load Defaults values for all the setup options. Save as User Defaults Save the changes done so far as user def

66 CSA-5200 Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on

67 CSA-5200 Consignes de Sécurité Importantes Pour assurer la sécurité de l’utilisateur, veuillez lire et suivre toutes les directives, ainsi que les

68 CSA-5200 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Z

69 CSA-5200 ADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33 (0) 1

7 CSA-5200 1.3 Mechanical Overview 1.3.1 Front Panel 1.3.2 Rear Panel

8 CSA-5200 1.3.3 Chassis Layout CFast Power SupplySATA Drive Bays SATADOMPower DDR3 DIMMs x4SATAConnectorsFans

9 CSA-5200 1.4 Mechanical Dimensions 1.4.1 Dimensions 458.8440482.676.2883.37465Dimensions in mm 440