Adlink cPCIS-1100A Series Manual do Utilizador Página 1

cPCIS-1100 Series 3U Height Subsystems for CompactPCI Modules User’s Manual Manual Rev.: 2.00 Date: Sept

6 • Getting Started System slots have obvious indicators (e.g. red card guide rail, triangle mark enclosing the slot number on the backplane, etc

Getting Started • 7 CompactPCI Card Installation/Removal Procedure 1. Place the sub-system on a level surface or rackmount it. Remove the blanking p

8 • Getting Started To remove the module, press the release button (if necessary), and reverse steps 1 through 5 above. 2.3 RTM (Rear T

Getting Started • 9 The installation and removal procedures for a RTM are the same as those for CompactPCI boards. Because they are shorter than front

10 • Getting Started This page intentionally left blank.

Backplane • 11 3 Backplane In this chapter, we will describe the backplanes for the cPCIS-1100 Series subsystems. The following table specifies the b

12 • Backplane Peripheral slots: 7 Peripheral Slots Rear I/O: P2 rear I/O with AB-type shroud (optional) Power Connectors: ATX connector x2, DC screw

Backplane • 13 cBP-3208[R] Rear View 1 - P2 Optional Rear I/O: 2 - P2 to 8 - P2

14 • Backplane Pin Assignment ¾ [1 – P1] System Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O)

Backplane • 15 ¾ [1 – P2] System Slot Pin Z A B C D E F 22 GND GA4 GA3 GA2 GA1 GA0 GND 21 GND CLK6 GND NC NC NC GND 20 GND CLK5 GND NC NC

Revision History Revision Release Date Description of Change(s) 2.00 September 15, 2014 Initial release Copyright 2014 ADLIN

16 • Backplane ¾ [2 – P1] / [8 – P1] Peripheral Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND 24 GND AD[1] +5V V(I/O)

Backplane • 17 ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15 GND

18 • Backplane 3.2 cBP-3206[R] Backplane The cBP-3206[R] is a 3U CompactPCI 32-bit backplane with optional rear I/O (designated by an “R” suffix). Th

Backplane • 19 Mechanical Drawing cBP-3206[R]Rear ViewcBP-3206[R]Front View1 - P21 - P16 - P26 - P1CN1 CN2 JP8 - JP101 - P2 Opt. Rear I/O: 2 - P2

20 • Backplane Pin Assignment ¾ [1 – P1] System Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O)

Backplane • 21 ¾ [1 – P2] System Slot Pin Z A B C D E F 22 GND GA4 GA3 GA2 GA1 GA0 GND 21 GND CLK6 GND NC NC NC GND 20 GND CLK5 GND NC NC

22 • Backplane ¾ [2 – P1] – [6 – P1] Peripheral Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND 24 GND AD[1] +5V V(I/O)

Backplane • 23 ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15

24 • Backplane 3.3 cBP-3061 Power Backplane The cBP-3061 is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for one power module. It is used by th

Backplane • 25 Pin Assignment ¾ CN1 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC ¾ CN2 – Power Sense

Table of Contents • iii Table of Contents 1 Introduction ...1 1.1 P

26 • Backplane ¾ CN4 – Modular Power 47P Connector Pin Signal Pin Signal 47 ACL/-DC IN 31 GA2 46 ACN/+DC IN 30 V1 SENSE 45 CGND 29 V1ADJ 4

Backplane • 27 ¾ CN7 –AC/DC in Let Connector Pin # Signal Name 1 ACN/DC+ 2 ACL/DC- 3 CGND ¾ CN8 – IPMB Connector Pin # Signal Name 1 IPMB_SCL

28 • Backplane 3.4 cBP-3062A Power Backplane The cBP-3062A is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for two power modules. It is used by

Backplane • 29 Pin Assignment ¾ CN1 / CN2 – Modular Power 47P Connector Pin Signal Pin Signal 47 ACL/-DC IN 31 GA2 46 ACN/+DC IN 30 V1 SENSE

30 • Backplane ¾ CN5 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC ¾ CN6 –Connector Pin # Signal Name

Backplane • 31 ¾ CN9 / CN10 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15

32 • Backplane This page intentionally left blank.

Power Supply Unit • 33 4 Power Supply Units The cPCIS-1100 Series subsystems are equipped with either the Zippy Technology Corp. PS2 HG2-6400P industr

34 • Power Supply Unit Input Characteristics • Voltage: 90 – 240 VAC Full Range • Frequency : 47 ~ 63 HZ • Input Current: 8.0 A ( RMS ) FOR 115

Power Supply Unit • 35 4.2 CompactPCI: cPS-H325/AC Features • 250W 3U x 8HP Eurocard package • Meets IEC1000-3-2 harmonic correction • Internal OR

iv • Table of Contents 4.2 CompactPCI: cPS-H325/AC...35 Features ...

36 • Power Supply Unit • Dielectric Withstand: Meets IEC950 regulation • EMI: Meets EN55022 / FCC Class A • Hold-up Time: 5mS after power fail sig

Power Supply Unit • 37 4.3 CompactPCI ETT PSU: cPS-P325/AC Features • 250W 3U x 8HP Eurocard package • Meets EN 61000-3-2 active power factor corre

38 • Power Supply Unit • Power Fail Signal: available at [FAL#] pin • Status LED: <green> means valid input voltage; <amber> means a cr

Power Supply Unit • 39 o Over Current Protection: Installed at each rail. o Overload Protection: Fully protected against output overload or short ci

40 • Power Supply Unit This page intentionally left blank.

Specifications • 41 5 Specifications 5.1 Features Standard 19” Rack-mount 3U CompactPCI form factor (3U height). Board Space: Supports both front and

42 • Specifications 5.3 Environmental Operating Temperature: 1. cPS-H325/AC: 0°C ~ +50°C ; 2. cPS-P325/AC: -25°C ~ +50°C (Up to 70°C but will have

Important Safety Instruction • 43 Important Safety Instructions Read and follow all instructions marked on the product and in the documentation before

44 • Important Safety Instruction If one of the following situations arises, get the equipment checked by a service personnel: A. The power cord or

Introduction • 1 1 Introduction 1.1 Product Definition The cPCIS-1100 Series Subsystems are rack mountable, 3U in height, and designed for 3U CompactP

2 • Introduction 1.2 Mechanical Drawing

Introduction • 3 1.3 Configurations The cPCI-1100 Series comes in the following configurations: System Slots Peripheral Slots PSU(s) Monitor PICMG c

4 • Introduction This page intentionally left blank.

Getting Started • 5 2 Getting Started In this chapter, we will describe the unpacking procedure of the sub-system and CompactPCI board and power suppl